Alphatek

How to Use Tile Levelling Clips (and Remove Them Cleanly)

Looking for a supplier? Alphatek supplies tile spacers and levelling systems in Dubai and the UAE: clips, wedges and caps for floor and wall tiling.

Large-format tiles look great, but even a small difference in height between two tiles (called lippage) catches the light and the foot. Tile levelling clips pull neighbouring tiles to the same height while the adhesive sets, and they set the joint width at the same time.

Here is how to choose the right clip, place it, tighten it and remove it cleanly.

Tile levelling clips and wedges laid out with a tiling kit

How a levelling system works

Each clip has a flat base that slides under the edges of two tiles and a strip that stands up in the joint. A wedge or cap is pushed or screwed onto the strip and presses both tiles down to the same level. Once the adhesive has set, the strip is snapped off at a weak line just below the tile surface, and the base stays hidden in the adhesive.

Choosing the clip size

  • Joint width: the strip thickness sets the joint, so pick the clip that matches the joint on your drawing (for example 1.5 mm, 2 mm or 3 mm)
  • Tile thickness: check the clip suits the tile thickness, especially for thick outdoor tiles or thin porcelain panels
  • Wedge or screw cap: wedges are fast on large floors; screw caps give finer control on walls and very large tiles

Work out how many clips to order with our tile levelling clip calculator.

Step by step

1. Spread the adhesive

Use the trowel size the adhesive maker recommends for the tile size, and back-butter large tiles for full coverage.

2. Place clips under the first tile

Slide the clip bases under the tile edges. As a guide, use two clips per side on medium tiles and three or more on long edges, with clips about 50 mm in from each corner.

3. Lay the next tile

Press the next tile down onto the other half of the clip bases so the strip sits in the joint.

4. Insert the wedges or caps

Push the wedge through the clip slot, or screw the cap down, until both tiles are pulled level. Use the pliers made for the system on big floors.

5. Do not over-tighten

Stop once the tiles are level. Too much force can lift the base or crack thin tiles.

6. Wait, then remove

Leave the clips until the adhesive has set as the maker specifies, usually at least a day.

Low pedestal with tile tabs supporting large outdoor tiles

How to remove tile levelling clips

  • Knock or kick the top of the clip along the line of the joint, never across the tile, so it snaps at the break line
  • For stiff clips, use a rubber mallet in the joint direction
  • Collect the wedges, as many systems let you reuse them
  • Clean any loose pieces out of the joints before grouting

Removing clips too early can let tiles move; removing them across the tile can chip the edge.

Frequently asked questions

What size tile levelling clips should I use?

Match the clip to the joint width on your drawing, such as 1.5 mm, 2 mm or 3 mm, and check it suits your tile thickness.

How many tile levelling clips do I need per tile?

It depends on the tile size. A 600 x 600 mm tile usually needs about two clips per side, and longer tiles need more. Our tile levelling clip calculator gives a total for your floor.

How do you remove tile levelling clips?

Once the adhesive has set, knock the top of each clip along the joint line with your foot or a rubber mallet so it snaps off below the tile surface. Do not hit it across the tile.

Can tile levelling wedges be reused?

Yes, wedges and screw caps can usually be reused. The clips are single-use, because the base stays in the adhesive.

Do I need a levelling system for wall tiles?

It helps a lot with large or thin wall tiles, where small height differences show in side light.

Need tile levelling clips in the UAE?

We supply clips, wedges and caps for contractors and tiling teams across Dubai and the UAE. For large tiles, see also our guide to tile levelling for large-format tiles. Request a quote or email sales@alphatek.ae.

Scroll to Top
Hi! 👋 Need a product or a quotation? Ask me.