Alphatek

GRP Water Tank Sizes and Panel Types: How to Choose (UAE)

Need a GRP water tank? Alphatek is a GRP water tank supplier in Dubai and the UAE: sectional and one-piece tanks to your capacity, plus GRP lining for existing tanks.

A GRP water tank has to fit three things: the water the building needs, the space on the roof or in the plant room, and the route the tank takes to get there. Get those right and the tank will serve for years without rust or leaks.

This guide explains how GRP water tank sizes work, the difference between sectional (panel) and one-piece tanks, and what to send your supplier for an accurate quotation.

GRP sectional water storage tank with access ladder on a residential roof in Dubai

Quick answer

QuestionShort answer
How is capacity worked out?Length x width x height of water. 1 m³ = 1,000 litres.
Sectional or one-piece?Sectional (panel) tanks for medium and large capacities or tight access; one-piece tanks for small capacities where the tank fits the route.
Where can it go?Roofs, plant rooms and ground level, on a level base or supports.
What do I send for a quote?Capacity, the space available, location, connection sizes and positions, and access needs.

How to work out GRP water tank capacity

Capacity is the internal length x width x height of the water. Because 1 m³ holds 1,000 litres, a tank of 3 m x 2 m x 2 m holds 12 m³, or 12,000 litres. The useful capacity is a little less than the full box, because space is left above the water line for the inlet valve, the overflow and air.

Tank (L x W x H)VolumeApproximate litres
2 m x 2 m x 2 m8 m³8,000
3 m x 2 m x 2 m12 m³12,000
4 m x 3 m x 2 m24 m³24,000
5 m x 4 m x 3 m60 m³60,000
6 m x 5 m x 3 m90 m³90,000

How much water the building needs is set by its design and by the consultant or authority on the project. If you only know the number of units or occupants, send that and the drawing, and we will help you arrive at a practical tank size.

Sectional (panel) GRP tanks

A sectional tank is assembled on site from GRP panels bolted together with sealing strips, with internal or external stays to hold the shape. Panels are commonly 1 m x 1 m, with half panels used to fine-tune the height. Because each panel is carried in on its own, a large tank can be built on a roof or in a basement plant room that no single tank could reach.

Sectional tanks can also be built with an internal partition, so one half can be emptied and cleaned while the other keeps supplying the building.

One-piece GRP tanks

A one-piece tank is delivered as a single unit, so it is quick to set in place and connect. It suits smaller capacities, for example villas and small buildings, as long as the tank fits through the gate, stairs, lift or crane route to its final position. Measure that route before choosing.

Roof, plant room or ground level?

  • Roof tanks: check the roof can carry the full weight of water, and plan a level base or steel supports. GRP does not rust in the sun and humidity, which is why it is popular on UAE roofs.
  • Plant rooms and basements: check headroom for the tank plus the manhole and ladder above it, and the access route for panels.
  • Ground level: place the tank on a level concrete base, with space around it for inspection.

Fittings to plan on the drawing

Mark the inlet, outlet, overflow, drain and vent sizes and positions, the manhole size and position, and whether you need internal and external GRP ladders. Sealed GRP seal plates and water tank access covers keep dust and insects out.

Old concrete or steel tank? Consider relining

If the problem is an old RCC or steel tank that leaks, it may not need replacing. GRP lining gives it a new watertight, smooth surface. Our GRP tank lining guide explains the steps.

Frequently asked questions

What size GRP water tank do I need?

It depends on the water the building uses and the storage the consultant or authority requires. Work out the volume with length x width x height (1 m³ = 1,000 litres) and send us the figure and the space available.

What panel sizes are used for GRP sectional tanks?

Panels are commonly 1 m x 1 m, with half panels used to adjust the height. The tank is built up from these panels to suit your capacity and space.

Is a sectional tank better than a one-piece tank?

Neither is better for every job. Sectional tanks suit larger capacities and difficult access; one-piece tanks are quick to install where the tank fits the access route.

Can a GRP tank be installed on a roof?

Yes. GRP is light and does not rust, which suits UAE roofs. The roof and the base or supports must be designed for the full weight of water.

How much does a GRP water tank cost?

It depends on the capacity, the tank type, the fittings and the site. Send us the size or drawing and we will reply with a quotation.

Need a GRP water tank?

Send us the capacity, the space available and your drawing or site photos, and we will propose the tank and reply with a quotation. Request a quote, call or WhatsApp +971 54 466 7243, or email sales@alphatek.ae.

Scroll to Top
Hi! 👋 Need a product or a quotation? Ask me.