Alphatek

Grease Trap Type A, B & C in Dubai: Which Size Do You Need?

Looking for a supplier? Alphatek is a grease trap supplier in Dubai and the UAE: PVC grease traps in Type A, B and C, above-ground units and oil interceptors, made to size.

If you are opening a restaurant, cafe, cloud kitchen or hotel kitchen in Dubai, the drawings will usually call for a grease trap of a certain type: Type A, Type B or Type C. The letters describe the size class of the trap, from small units near a sink to large traps that serve a whole kitchen. Picking the right one avoids blocked drains, bad smells and failed inspections.

This guide explains what each type is used for, how the size is worked out and what to check before you order.

PVC grease trap recessed into a commercial kitchen floor in Dubai

Type A, B and C at a glance

TypeTypical useUsual position
Type ASmall pantries, coffee shops, juice bars, single sinksUnder or next to the sink
Type BSmall and medium restaurants, cafes with a cooking line, staff canteensInside the kitchen, above floor or recessed
Type CLarge restaurants, hotel kitchens, central kitchens, food courtsRecessed in the floor or in a service area, often serving several fixtures

The exact type and capacity for your outlet is set by the approved drainage design and the municipality requirements for your location. Use the table as a starting point, not as an approval.

How grease trap size is worked out

Grease traps are sized on how much greasy water reaches them and how long that water needs to stay in the trap so fat can float and solids can settle. The main inputs are:

  • Meals or covers served in the busiest hour
  • Kitchen type: full cooking line with a dishwasher, hand washing only, or takeaway with single-use plates
  • Opening hours, which decide how much grease builds up between cleanings
  • Fixtures connected: pot sinks, prep sinks, floor drains, dishwashers and combi ovens
  • Food waste disposers, which add a lot of solids and need extra volume

Our free grease trap size calculator uses these inputs to give a rough volume in litres and suggests whether an under-sink, above-ground or larger in-floor trap fits.

PVC grease trap installed in a restaurant kitchen in Dubai

Where the trap should go

  • As close as practical to the fixtures it serves, so grease does not cool and stick inside long pipes
  • Where the cover can be lifted and the baskets emptied without moving equipment
  • Away from food preparation surfaces, with a sealed, gasketed cover to keep odours in
  • With a vent and an outlet that match the drainage layout, so the trap does not siphon

Dishwashers and combi ovens discharge hot water. Many designs connect them after a short cooling run or to a larger trap, so check the drawing before connecting everything to a small Type A unit.

What inspectors and FM teams look for

  • The trap type and size match the approved drawing
  • The cover is sealed and can be opened for inspection
  • Sediment baskets are in place and the trap is not full of fat
  • A cleaning log or contract with an approved waste collector
  • No direct connection that bypasses the trap

For cleaning intervals, see our guide on how often to clean a grease trap.

PVC grease traps from Alphatek

Our grease traps are fabricated from 7.7 mm thick BS EN 1401 PVC sheet, which does not rust or corrode in kitchen water. Each unit has a 15 mm PVC cover with a rubber gasket and stainless steel bolts, removable sediment buckets with handles, a vent connection and an oil drain. Because they are fabricated, the size, depth and inlet and outlet positions can follow your drawing. To compare materials, read PVC vs stainless steel vs concrete grease traps.

Frequently asked questions

What is the difference between grease trap Type A, B and C?

They are size classes. Type A is the smallest, usually under or next to a single sink. Type B suits small and medium restaurants. Type C is the largest and serves busy kitchens such as hotels, central kitchens and food courts.

Which grease trap type does Dubai Municipality require for my restaurant?

The required type and capacity depend on your kitchen, its fixtures and the approved drainage design. Your MEP consultant or contractor confirms it with the authority. We can supply the type and size shown on your drawing.

Can one large grease trap serve the whole kitchen?

Yes, many kitchens use one Type C trap that serves several sinks and floor drains, as long as the pipe runs, falls and venting follow the design. Small outlets often use a Type A or B unit near the fixtures instead.

How do I know what size grease trap I need?

Start with the meals served in your busiest hour, the type of kitchen and the opening hours. Our grease trap size calculator gives a rough volume, and we can check it against your drawings before you order.

Are PVC grease traps accepted in Dubai?

PVC grease traps are widely used in UAE kitchens because they do not corrode. Always follow the material shown on your approved drawing and specification.

Need a grease trap quotation?

Send us the drawing or tell us the kitchen type, meals per hour and the trap type on your plan. We supply grease traps across Dubai, Abu Dhabi, Sharjah and the rest of the UAE. Request a quote or email sales@alphatek.ae.

Scroll to Top
Hi! 👋 Need a product or a quotation? Ask me.