Alphatek

Linear Shower Drain Problems: Slow Draining, Smells, Leaks and Standing Water

Replacing or upgrading a linear shower drain? Alphatek supplies linear shower drains in SS 304/316, including tile-insert linear drains and square-pattern grates, for villas, apartments and hotels in Dubai and across the UAE.

Linear shower drains look clean and make walk-in showers possible, but when something goes wrong the whole bathroom suffers: water pools on the floor, smells come up, or water finds its way under the tiles. Almost every problem traces back to one of a few causes: blockage, wrong floor falls, a dry or missing water seal, or poor waterproofing around the drain.

Here are the common linear shower drain problems, what causes them and how they are usually fixed.

600 mm linear shower drain in a walk-in shower

Quick guide: problem, cause, fix

ProblemLikely causeUsual fix
Water drains slowlyHair and soap in the trap or grate; outlet too small for the shower flowClean the grate and trap insert; check the outlet size against the shower head flow
Water stands on the floorFloor falls run the wrong way or are too flat; drain set too highRe-lay the tiles with proper falls towards the drain
Drain smellsDry water seal, missing or loose trap insertRun water regularly; refit or replace the trap insert
Water under tiles or leaking belowWaterproofing membrane not sealed to the drain flangeRemove the tiles around the drain and re-seal the membrane to the flange
Grate rattles or rocksDrain body not level or not fully beddedRe-bed or adjust the height of the drain body
Tile-insert tray cracks or sagsTile not bedded fully in the trayRemove and re-bed the tile in the tray

1. Slow draining

The most common cause is simple: hair and soap build up in the grate and the trap insert under it. Lift the grate, take out the trap insert and clean both. If the shower still floods even when clean, the drain may be too small for the water flow, especially with rain shower heads. In that case the outlet and channel size need checking against the shower flow, which is easier to get right at design stage; see our linear shower drain design tips.

2. Standing water on the floor

Water should run to the drain along the floor falls. If the tiles are flat, fall the wrong way, or the drain body was set slightly too high, water stays on the floor. Small adjustments rarely fix it; usually the tiles around the drain must be re-laid with proper falls. Getting the falls and drain height right during installation avoids this; our linear shower drain installation guide covers the steps.

3. Smells

Linear drains rely on a trap insert or trap under the outlet to hold a water seal. In guest bathrooms or apartments left empty for weeks, the seal dries out and smells come up. Running water for a minute normally fixes it. If the trap insert is missing, cracked or not seated properly, replace or refit it. See why floor drains smell for other causes.

4. Leaks under the tiles

A linear drain must be part of the waterproofing, not just sit in it. The waterproofing membrane has to be bonded and sealed to the drain flange. If it is not, water gets past the drain into the screed, and shows up later as damp walls, stained ceilings below or loose tiles. The repair is to remove the tiles around the drain and re-seal the membrane properly. Choose drains with a proper flange for membrane connection from the start.

5. Rattling grates and cracked tile inserts

A grate that rattles or rocks usually means the drain body is not level or not fully bedded. For tile-insert drains, the tile must be fully bedded in the tray; a hollow tile cracks under foot. Both are installation issues that can be corrected by re-bedding.

Material and grade

Stainless steel SS 304 suits most bathrooms. For hotel spas, pool showers and coastal buildings, SS 316 resists staining much better. See SS 304 vs SS 316 for the difference.

Frequently asked questions

Why is my linear shower drain draining slowly?

Usually because hair and soap have built up in the grate and trap insert. Clean both. If the drain is still slow, the outlet or channel may be too small for the shower flow.

Why does water stay on my shower floor?

The floor falls are wrong or too flat, or the drain was set too high. The tiles around the drain normally need to be re-laid with proper falls towards the drain.

Why does my linear shower drain smell?

The water seal in the trap insert has dried out, or the insert is missing or loose. Run water to refill the seal, or refit or replace the insert.

Why is water leaking under my linear shower drain?

The waterproofing membrane is not sealed to the drain flange, so water passes into the screed. The tiles around the drain need to be removed and the membrane re-sealed to the flange.

How do I clean a linear shower drain?

Lift the grate, remove the trap insert, clear hair and soap, rinse both and refit them. Doing this regularly prevents most slow-draining problems.

Need a replacement or new linear shower drain?

Send us the drain length, outlet type, grate style or tile-insert, finish and quantities, and we will reply with options and a price for Dubai and the rest of the UAE. Request a quote, call or WhatsApp Justin Varghese on +971 54 466 7243, or email sales@alphatek.ae.

Scroll to Top
Hi! 👋 Need a product or a quotation? Ask me.